| NetPA U 8001 SUB |
|
| Audio system |
| Frequency response | |
| Line in to line out | 20 Hz to 20 kHz, ±0.5 dB |
| Line in to digital out | 20 Hz to 20 kHz, ±0.5 dB |
| Digital in to line out | 20 Hz to 20 kHz, ±0.5 dB |
| Through amplifier | 20 Hz to 1 kHz, ±1 dB |
| THD + Noise | |
| Through DSP | <0.01% @ 1 kHz at maximum output level |
| Through amplifier | 0.1% @ 1 kHz at 3 dB below clipping |
| S/N | |
| Line in to line out | 90 dB, 20 Hz to 20 kHz at maximum output (unweighted) |
| Line in to speaker out | 100 dB, 20 Hz to 1 kHz at maximum output (unweighted) |
| Line in to digital out | 90 dB, 20 Hz to 20 kHz at maximum output (unweighted) |
| Digital in to line out | 100 dB, 20 Hz to 20 kHz at maximum output (unweighted) |
| Digital in to speaker out | 100 dB, 20 Hz to 1 kHz at maximum output (unweighted) |
| Crosstalk | <-90 dB @ 1 kHz, fully loaded |
| Volume control | -100 dB to 0 dB (control 0 to 100 in 0.1 dB steps) |
|
| Audio Input (line inputs) |
| Number/signal type | 2 mono, line, balanced/unbalanced |
| Connector | (1) 3.5 mm captive screw connector, 5 pole, mono, balanced/unbalanced |
| Impedance | >10k ohms unbalanced/balanced |
| Nominal level | +4 dBu, -10 dBV adjustable via input gain |
| Maximum level | +21 dBu at rated THD+N when input gain is set to 0 dB |
| Input sensitivity | |
| Line input | +21 dBu, all gains / attenuators in signal path set to 0 dB |
| AT input | 0 dBFS, all gains / attenuators in signal path set to 0 dB |
| CMRR | >60 dB typical |
| Input gain adjustment | -18 dB to +24 dB in 0.1 dB steps, adjustable per input |
|
| Audio line output |
| Number/signal type | 2 mono, line, balanced/unbalanced |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | 100 ohms balanced, 50 ohms unbalanced |
| Gain error | ±0.1 dB channel to channel |
| Maximum level (Hi-Z) | >+21 dBu balanced; +15 dBu unbalanced |
|
| Audio processing |
| D/A conversion | 24 bit, 48 kHz |
|
| AT port — Audio Transport |
| Transmission type | Dante/AES-67, software selectable |
| Connectivity | 1 RJ-45 connector, 1-port 100 Mbps to Dante interface |
| Inputs | 2 channels Rx (2 flows, unicast or multicast) |
| Outputs | 2 channel Tx (2 flows, unicast or multicast) |
| Audio format | 24-bit uncompressed, selectable at 44.1, 48, 88.2, and 96 kHz sampling rate |
| Latency | Deterministic, based on user selection: 1.0 ms (default), 2.0 ms, 5.0 ms |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio speaker output |
| Number/signal type | 1 channel, 2, 4, or 8 ohms |
| Connector | (1) 5 mm screw lock captive screw connector, 2-pole |
| NOTE | This connector accepts wires of 22 AWG to 12 AWG |
|
| Load impedance | 2 ohms minimum |
| Amplifier type | Class D |
| Output power | |
| 8 ohms | 800 watts, 8 ohms, 100 Hz, <0.1% THD |
| 4 ohms | 650 watts, 4 ohms, 100 Hz, <0.1% THD |
| 2 ohms | 325 watts, 2 ohms, 100 Hz, <0.1% THD |
|
| Control/Remote |
| Control port | (1) 3.5 mm captive screw connector, 5 pole |
| Serial | |
| Serial host control port | 1 bidirectional RS-232 |
| Baud rate and protocol | 38400 baud, 8 data bits, 1 stop bit, no parity |
| Pin configuration | Pin 1 = Tx, Pin 2 = Rx, Pin 3 = Gnd |
| Standby | |
| Standby power control | Contact closure |
| Pin configuration | Pin 4 = Gnd, Pin 5 = Standby |
| USB control port | 1 rear panel female USB Mini-B |
| USB standards | USB 2.0, high speed |
| Ethernet host port | 1 RJ-45 female connector |
| Ethernet data rate | 10/100Base-T |
| Program control | Configuration program for Windows®, Extron Simple Instruction Set (SIS™) |
|
| General |
| Power supply | Internal Input: 100-240 VAC, 50-60 Hz, 0.5 A |
| Power consumption and thermal dissipation | |
| |
| NetPA U 8001 SUB |
115 VAC, 60Hz |
230 VAC, 50Hz |
AC Line
Current |
AC Power
Consumed |
Thermal
Dissipation |
AC Line
Current |
AC Power
Consumed |
Thermal
Dissipation |
| Condition |
A |
W |
W |
BTU/hr |
A |
W |
W |
BTU/hr |
Active (1/8 power), all
channels driven |
8Ω |
1.1 |
121 |
21 |
72 |
0.6 |
118.7 |
18.7 |
64 |
| 4Ω |
1.0 |
104.7 |
23.5 |
80 |
0.6 |
102.8 |
21.6 |
74 |
| 2Ω |
0.6 |
61.1 |
20.5 |
70 |
0.4 |
60 |
19.4 |
66 |
| Quiescent (idle) |
0.2 |
10.4 |
10.4 |
35 |
0.2 |
10.2 |
10.2 |
35 |
| Standby |
<0.1 |
<4 |
<4 |
<14 |
<0.1 |
<4 |
<4 |
<14 |
|
| Ambient temperature/humidity | |
| Storage | -40 to +158 °F (-40 to +70 °C) / 10% to 90%, non-condensing |
| Operating | +32° to +122° F (0° to +50° C) / 10% to 90%, non-condensing |
| Cooling | Convection, no vents |
| Protection | Clip limiter, thermal, short circuit, DC output |
| Indication | Limiter/Protect LED indicates the onset of clip limiting, thermal cycling, or a short circuit.
Power LED indicates power state, DC output protection (see NetPA U 8001 SUB User Guide for details). |
| Mounting | |
| Rack mount | Yes, with included brackets or optional 1U rack shelf |
| Subwoofer mount | Yes, with optional mounting hardware (included with SF 10C SUB) |
| Enclosure type | Metal |
| Enclosure dimensions | 1.7" H x 8.7" W x 10.5" D (1U high, half rack wide) (43 mm H x 221 mm W x 267 mm D) |
| Product weight | 4.2 lbs (1.9 kg) |
| Regulatory compliance | |
| Safety | CE, C-tick, c-UL, KC, UL rated for use in plenum airspaces, meets UL 2043 for heat and smoke release |
| EMI/EMC | CE, C-tick, FCC Class B, ICES, VCCI Class B, CISPR 22 Class B |
| Environmental Compliance | Ecofficient Level 3, RoHS |
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (6406-D5) |