近期查看的产品
MPA 601
建筑工程规范
选择一个产品编号:
复制文本
已复制!
发生错误。请稍后重试。
MPA 601-70V
- Provide a compact, energy efficient audio power amplifier that shall support three analog stereo or mono inputs and one amplified mono analog output with 60 watts rms into a 70 volt line.
- Compact mono amplifier with 60 watts rms power output into a 70 volt line and Ecofficient Level 3 qualification
- Input Requirements
- Shall support one stereo, balanced or unbalanced signal on one 5-pole, 3.5 mm captive screw connector
- Shall support one stereo, unbalanced signal on one pair of RCA connectors
- Shall support one stereo, unbalanced signal on one 3.5 mm stereo mini jack
- Shall provide individual buffering for each input
- Shall provide stereo input summing of all inputs into a single mono signal
- Output Requirements
- Shall support one mono speaker level signal on one 2-pole, 5 mm captive screw connector
- Shall provide a total of 60 watts rms output power into a 70 volt line measured at 1 kHz with 1% THD
- Shall provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Shall support a minimum load impedance of 83 ohms
- Shall provide a THD+N measurement of less than 0.1% measured at 1 kHz and 3 dB below clipping
- Shall provide damping factor of greater than 100
- Shall provide a high pass filter for frequencies below 80 Hz with a 12 dB per octave rolloff
- Amplifier Requirements
- Shall utilize an efficient Class D amplifier design
- Shall provide Class D Ripple Suppression technology
- Shall be convection cooled and operate without fans or vents
- Shall provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain without audible artifacts to eliminate clipping distortion
- Power Requirements
- In conjunction with power supply, shall draw 14.8 watts during typical (1/8 power) operation
- In conjunction with power supply, shall draw 6.2 watts during quiescent operation
- Shall provide a low power standby mode
- Shall enter standby mode after 25 minutes (+/- 5 minutes) of inactivity
- Shall draw less than 1 watt while in standby mode
- Shall return to full power status in less than one second upon signal detection while in standby mode
- Shall feature an input signal detection threshold of -44 dBV, +/- 3 dB on unbalanced RCA and 3.5 mm stereo mini jack inputs to deactivate standby mode
- Shall feature an input signal detection threshold of -30 dBu, +/- 3 dB on balanced captive screw connector input to deactivate standby mode
- Shall meet Ecofficient Level 3 requirements
- Shall provide energy-efficient external universal power supply with 2-pole captive screw connector
- Shall be universal in-line power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall provide output of 12 VDC, 3 A, 36 watts
- Shall support use of optional Extron ZipClip™ 200 mounting bracket
- Shall meet energy efficiency level V and bear the UL Environment Energy Efficiency Certification (EEC) Mark
- Control Requirements
- Shall support remote control of volume and muting on 3-pole, 3.5 mm captive screw connector using optional Extron analog volume and mute controllers
- Front Panel Requirements
- Shall provide an LED for power indication that lights green when the unit is receiving power and active, and lights amber when the unit is in standby mode
- Shall provide potentiometers for bass, treble, and input level adjustment
- Rear Panel Requirements
- Shall provide one input on one 5-pole, 3.5 mm captive screw connector
- Shall provide one input on one pair of RCA connectors
- Shall provide one input on one 3.5 mm stereo mini jack
- Shall provide one output on one 2-pole, 5 mm captive screw connector
- Shall provide remote volume and mute control port on one 3-pole, 3.5 mm captive screw connector
- General Requirements
- Shall be enclosed in a rack-mountable 1U, quarter rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall be UL rated for use in plenum airspaces and meet UL 2043 compliance for heat and smoke release, excluding the power supply
- Shall meet UL 60065 and IEC 60065 for safety
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class B, ICES Class B, KCC, and VCCI
- Shall comply with appropriate requirements of CEC, EU code of conduct, RoHS, and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron MPA 601-70V, part number 60-1449-01; no alternates or equals.
- Compact mono amplifier with 60 watts rms power output into a 70 volt line and Ecofficient Level 3 qualification
MPA 601-70V
- Provide a compact, energy efficient audio power amplifier that shall support three analog stereo or mono inputs and one amplified mono analog output with 60 watts rms into a 70 volt line.
- Compact mono amplifier with 60 watts rms power output into a 70 volt line and Ecofficient Level 3 qualification
- Input Requirements
- Shall support one stereo, balanced or unbalanced signal on one 5-pole, 3.5 mm captive screw connector
- Shall support one stereo, unbalanced signal on one pair of RCA connectors
- Shall support one stereo, unbalanced signal on one 3.5 mm stereo mini jack
- Shall provide individual buffering for each input
- Shall provide stereo input summing of all inputs into a single mono signal
- Output Requirements
- Shall support one mono speaker level signal on one 2-pole, 5 mm captive screw connector
- Shall provide a total of 60 watts rms output power into a 70 volt line measured at 1 kHz with 1% THD
- Shall provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Shall support a minimum load impedance of 83 ohms
- Shall provide a THD+N measurement of less than 0.1% measured at 1 kHz and 3 dB below clipping
- Shall provide damping factor of greater than 100
- Shall provide a high pass filter for frequencies below 80 Hz with a 12 dB per octave rolloff
- Amplifier Requirements
- Shall utilize an efficient Class D amplifier design
- Shall provide Class D Ripple Suppression technology
- Shall be convection cooled and operate without fans or vents
- Shall provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain without audible artifacts to eliminate clipping distortion
- Power Requirements
- In conjunction with power supply, shall draw 14.8 watts during typical (1/8 power) operation
- In conjunction with power supply, shall draw 6.2 watts during quiescent operation
- Shall provide a low power standby mode
- Shall enter standby mode after 25 minutes (+/- 5 minutes) of inactivity
- Shall draw less than 1 watt while in standby mode
- Shall return to full power status in less than one second upon signal detection while in standby mode
- Shall feature an input signal detection threshold of -44 dBV, +/- 3 dB on unbalanced RCA and 3.5 mm stereo mini jack inputs to deactivate standby mode
- Shall feature an input signal detection threshold of -30 dBu, +/- 3 dB on balanced captive screw connector input to deactivate standby mode
- Shall meet Ecofficient Level 3 requirements
- Shall provide energy-efficient external universal power supply with 2-pole captive screw connector
- Shall be universal in-line power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall provide output of 12 VDC, 3 A, 36 watts
- Shall support use of optional Extron ZipClip™ 200 mounting bracket
- Shall meet energy efficiency level V and bear the UL Environment Energy Efficiency Certification (EEC) Mark
- Control Requirements
- Shall support remote control of volume and muting on 3-pole, 3.5 mm captive screw connector using optional Extron analog volume and mute controllers
- Front Panel Requirements
- Shall provide an LED for power indication that lights green when the unit is receiving power and active, and lights amber when the unit is in standby mode
- Shall provide potentiometers for bass, treble, and input level adjustment
- Rear Panel Requirements
- Shall provide one input on one 5-pole, 3.5 mm captive screw connector
- Shall provide one input on one pair of RCA connectors
- Shall provide one input on one 3.5 mm stereo mini jack
- Shall provide one output on one 2-pole, 5 mm captive screw connector
- Shall provide remote volume and mute control port on one 3-pole, 3.5 mm captive screw connector
- General Requirements
- Shall be enclosed in a rack-mountable 1U, quarter rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall be UL rated for use in plenum airspaces and meet UL 2043 compliance for heat and smoke release, excluding the power supply
- Shall meet UL 60065 and IEC 60065 for safety
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class B, ICES Class B, KCC, and VCCI
- Shall comply with appropriate requirements of CEC, EU code of conduct, RoHS, and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron MPA 601-70V, part number 60-1449-01; no alternates or equals.
- Compact mono amplifier with 60 watts rms power output into a 70 volt line and Ecofficient Level 3 qualification
MPA 601-100V
- Provide a compact, energy efficient audio power amplifier that shall support three analog stereo or mono inputs and one amplified mono analog output with 60 watts rms into a 100 volt line.
- Compact mono amplifier with 60 watts rms power output into a 100 volt line and Ecofficient Level 3 qualification
- Input Requirements
- Shall support one stereo, balanced or unbalanced signal on one 5-pole, 3.5 mm captive screw connector
- Shall support one stereo, unbalanced signal on one pair of RCA connectors
- Shall support one stereo, unbalanced signal on one 3.5 mm stereo mini jack
- Shall provide individual buffering for each input
- Shall provide stereo input summing of all inputs into a single mono signal
- Output Requirements
- Shall support one mono speaker level signal on one 2-pole, 5 mm captive screw connector
- Shall provide a total of 60 watts rms output power into a 100 volt line measured at 1 kHz with 1% THD
- Shall provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Shall support a minimum load impedance of 83 ohms
- Shall provide a THD+N measurement of less than 0.1% measured at 1 kHz and 3 dB below clipping
- Shall provide damping factor of greater than 100
- Shall provide a high pass filter for frequencies below 80 Hz with a 12 dB per octave rolloff
- Amplifier Requirements
- Shall utilize an efficient Class D amplifier design
- Shall provide Class D Ripple Suppression technology
- Shall be convection cooled and operate without fans or vents
- Shall provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain without audible artifacts to eliminate clipping distortion
- Power Requirements
- In conjunction with power supply, shall draw 14.8 watts during typical (1/8 power) operation
- In conjunction with power supply, shall draw 6.2 watts during quiescent operation
- Shall provide a low power standby mode
- Shall enter standby mode after 25 minutes (+/- 5 minutes) of inactivity
- Shall draw less than 1 watt while in standby mode
- Shall return to full power status in less than one second upon signal detection while in standby mode
- Shall feature an input signal detection threshold of -44 dBV, +/- 3 dB on unbalanced RCA and 3.5 mm stereo mini jack inputs to deactivate standby mode
- Shall feature an input signal detection threshold of -30 dBu, +/- 3 dB on balanced captive screw connector input to deactivate standby mode
- Shall meet Ecofficient Level 3 requirements
- Shall provide energy-efficient external universal power supply with 2-pole captive screw connector
- Shall be universal in-line power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall provide output of 12 VDC, 3 A, 36 watts
- Shall support use of optional Extron ZipClip™ 200 mounting bracket
- Shall meet energy efficiency level V and bear the UL Environment Energy Efficiency Certification (EEC) Mark
- Control Requirements
- Shall support remote control of volume and muting on 3-pole, 3.5 mm captive screw connector using optional Extron analog volume and mute controllers
- Front Panel Requirements
- Shall provide an LED for power indication that lights green when the unit is receiving power and active, and lights amber when the unit is in standby mode
- Shall provide potentiometers for bass, treble, and input level adjustment
- Rear Panel Requirements
- Shall provide one input on one 5-pole, 3.5 mm captive screw connector
- Shall provide one input on one pair of RCA connectors
- Shall provide one input on one 3.5 mm stereo mini jack
- Shall provide one output on one 2-pole, 5 mm captive screw connector
- Shall provide remote volume and mute control port on one 3-pole, 3.5 mm captive screw connector
- General Requirements
- Shall be enclosed in a rack-mountable 1U, quarter rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall be UL rated for use in plenum airspaces and meet UL 2043 compliance for heat and smoke release, excluding the power supply
- Shall meet UL 60065 and IEC 60065 for safety
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class B, ICES Class B, and VCCI
- Shall comply with appropriate requirements of CEC, EU code of conduct, RoHS, and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron MPA 601-100V, part number 60-1449-11; no alternates or equals.
- Compact mono amplifier with 60 watts rms power output into a 100 volt line and Ecofficient Level 3 qualification
MPA 601-100V
- Provide a compact, energy efficient audio power amplifier that shall support three analog stereo or mono inputs and one amplified mono analog output with 60 watts rms into a 100 volt line.
- Compact mono amplifier with 60 watts rms power output into a 100 volt line and Ecofficient Level 3 qualification
- Input Requirements
- Shall support one stereo, balanced or unbalanced signal on one 5-pole, 3.5 mm captive screw connector
- Shall support one stereo, unbalanced signal on one pair of RCA connectors
- Shall support one stereo, unbalanced signal on one 3.5 mm stereo mini jack
- Shall provide individual buffering for each input
- Shall provide stereo input summing of all inputs into a single mono signal
- Output Requirements
- Shall support one mono speaker level signal on one 2-pole, 5 mm captive screw connector
- Shall provide a total of 60 watts rms output power into a 100 volt line measured at 1 kHz with 1% THD
- Shall provide a signal-to-noise ratio of greater than 90 dB measured from 20 Hz to 20 kHz, unweighted
- Shall support a minimum load impedance of 83 ohms
- Shall provide a THD+N measurement of less than 0.1% measured at 1 kHz and 3 dB below clipping
- Shall provide damping factor of greater than 100
- Shall provide a high pass filter for frequencies below 80 Hz with a 12 dB per octave rolloff
- Amplifier Requirements
- Shall utilize an efficient Class D amplifier design
- Shall provide Class D Ripple Suppression technology
- Shall be convection cooled and operate without fans or vents
- Shall provide an automatic clip limiter to detect onset of clipping by comparing input and output waveforms and automatically reduce gain without audible artifacts to eliminate clipping distortion
- Power Requirements
- In conjunction with power supply, shall draw 14.8 watts during typical (1/8 power) operation
- In conjunction with power supply, shall draw 6.2 watts during quiescent operation
- Shall provide a low power standby mode
- Shall enter standby mode after 25 minutes (+/- 5 minutes) of inactivity
- Shall draw less than 1 watt while in standby mode
- Shall return to full power status in less than one second upon signal detection while in standby mode
- Shall feature an input signal detection threshold of -44 dBV, +/- 3 dB on unbalanced RCA and 3.5 mm stereo mini jack inputs to deactivate standby mode
- Shall feature an input signal detection threshold of -30 dBu, +/- 3 dB on balanced captive screw connector input to deactivate standby mode
- Shall meet Ecofficient Level 3 requirements
- Shall provide energy-efficient external universal power supply with 2-pole captive screw connector
- Shall be universal in-line power supply with IEC power socket and support for international 100-240 VAC, 50/60 Hz standards
- Shall provide output of 12 VDC, 3 A, 36 watts
- Shall support use of optional Extron ZipClip™ 200 mounting bracket
- Shall meet energy efficiency level V and bear the UL Environment Energy Efficiency Certification (EEC) Mark
- Control Requirements
- Shall support remote control of volume and muting on 3-pole, 3.5 mm captive screw connector using optional Extron analog volume and mute controllers
- Front Panel Requirements
- Shall provide an LED for power indication that lights green when the unit is receiving power and active, and lights amber when the unit is in standby mode
- Shall provide potentiometers for bass, treble, and input level adjustment
- Rear Panel Requirements
- Shall provide one input on one 5-pole, 3.5 mm captive screw connector
- Shall provide one input on one pair of RCA connectors
- Shall provide one input on one 3.5 mm stereo mini jack
- Shall provide one output on one 2-pole, 5 mm captive screw connector
- Shall provide remote volume and mute control port on one 3-pole, 3.5 mm captive screw connector
- General Requirements
- Shall be enclosed in a rack-mountable 1U, quarter rack width metal enclosure
- Shall meet regulatory compliances
- Shall meet safety compliances under CE, c-UL, and UL
- Shall be UL rated for use in plenum airspaces and meet UL 2043 compliance for heat and smoke release, excluding the power supply
- Shall meet UL 60065 and IEC 60065 for safety
- Shall meet EMI/EMC compliances under CE, C-tick, FCC Class B, ICES Class B, and VCCI
- Shall comply with appropriate requirements of CEC, EU code of conduct, RoHS, and WEEE
- Shall provide three year parts and labor warranty
- Input Requirements
- Approved device shall be the Extron MPA 601-100V, part number 60-1449-11; no alternates or equals.
- Compact mono amplifier with 60 watts rms power output into a 100 volt line and Ecofficient Level 3 qualification
把商品添加到购物车
Order Message Number
产品编号
注: 使用通用交流电源插座的 Extron 产品可支持多种不同的交流电源插头类型。在使用之前,确保设备满足您所在区域的所有规定要求,并符合所有应用的本地安全和电气规程及标准。
当前总计:

Chrome
Firefox
Edge
Safari